ThermoTek 28000 cfm Make Up Air Unit - Heat Only

Description

VERTICAL INDUSTRIAL HEATER WITH 36" BURNER AND 30"
BLOWER
No longer needed for new construction project due to design change.  Save money and time with this brand new, ready to install heated make up air unit.
Unit just completed and is ready to ship, or pickup in the Chicagoland area.
ThermoTek submittal sheets available upon request.
Fan #1 TTV 30
(2963 lbs./362 curb)
VERTICAL INDUSTRIAL HEATER WITH 36" BURNER AND 30"
BLOWER
Supply Motor:
Model DTP0204, 20.000 HP, 3 Phase, 460 V, 60Hz, 24.3 FLA, ODP,
Premium (E-Plus3) E
ff
.
Supply Motor Pulleys:
Part Type
Qty
Browning #
Turns Out
Belt
2
5VX950
Blower Pulley
1
2B5V234
Motor Pulley
1
2VP65 x 1 5/8
3.0
Burner:
Min Output BTU: 57,000 BTU/Hr
Max Output BTU: 1,710,000 BTU/Hr
Size: 36" long
Gas Type: Natural
Supply Performance:
Volume: 28000 cfm
RPM: 434
TS: 3409 ft/min
SP: 0.686" w.g.
0.500" Ext. + 0.186" Int.
BHP: 13.204
Heating Schedule:
Altitude: 2363'
Winter Entering Air Dry Bulb Temp: 33°F
Temp Rise: 56°F
Output BTU: 1693440
Input BTU: 1840696
BTUs BASED OFF STANDARD AIR DENSITY
Supply Installation Information:
Gas Inlet Pressure: 1 lb. - 5 lb.
Insurance: FM Insurance Requirement
Unit Main Input: 31.5 Amps MCA, 50 Amps MOP, 460 V, 8 AWG Wire
Min.
Supply Unit Voltage: 3 phs 460 V 60Hz
SCCR: 10 kAmp
Blower:
BLOWER 30" - Enamel
fi
nish, pillow block bearing, 0-51000 CFM, 50
HP, 2 7/16 x 65" Shaft, 650 MAX RPM, used in heated and non-
heated supply fans
Temp Control:
50-90°F Industrial Space Temp Control • Heating Activation Based
On Either Intake or Space Set Point • Manual Blower Mode. Use with
MUA.
Intake:
V-BANK - 53.25" Wide X 83.5" Long X 32" High for Vertical Industrial.
Standard 2" EZ Filter With Filter Intake Screen. For outdoor use.
Filters:
5x MV EZ Kleen Metal Mesh Filter. 20"x 25"x 2" Used for heater and
supply fan intakes. (3416)
20x MV EZ Kleen Metal Mesh Filter. 16"x 25"x 2" Used for heater and
supply fan intakes. (3410)
Curb & Supports:
Vertical stand for Size 4 Industrial Vertical Heaters (Outdoor). 60"
Wide x 89" Long x 76" High.
Selected Options:
Gas Pressure Gauge, 0-15#, 2.5" Diameter, 1/4" Thread Size
Gas Pressure Gauge, -5 to +15 Inches Wc., 2.5" Diameter, 1/4"
Thread Size
Ship Loose Gas Strainer. To be installed upstream of unit
connection. 1" Connection
Low Fire Start. Allows the burner circuit to energize when the
modulation control is in a low
fi
re position.
Freezestat factory set at 35°F and 10 minutes.
Burner section cap for size 4 Industrial Vertical unit with 27 or 30
blowers, protects burner section from weather prior to install. There
is no warranty for water damage in burner and/or gas train due to
improper storage prior to install.
Detector/Alarm Interlock (By Others)
High Gas Pressure Switch (1" - 20" WC) Factory set at 8" w.c.
Replaces part HGP-A.
Low Pressure Gas Switch (1" - 6" WC) Factory set at 2" w.c.
Option to control layer for 2nd limit switch.
Exhaust Relay Before Air
fl
ow Switch. Provides 2 sets of NO to be
used as a start command interlock for exhaust fans.
Size 4 Vertical Heater VAV Pro
fi
le and Wiring Package w/ Building
Static Pressure Control used with MUA board
Supply Variable Frequency Drive - 20 HP Max., 400/480 V, Three
Phase, 31.0/27.0 A Max., NEMA 1 Enclosure, (Default is Shipped
Loose for Field Installation) PART NEEDS PROGRAMMING
VFD factory mounted and wired on unit control panel.
Non-Fused Disconnect Switch for Industrial Make Up Air Units,
Single Point Connection.
Industrial GM - BTU 1650000 - 2199999 - 1 lb. - 5 lb., FM
Insurance Requirement, BV250-88, 1" Connection.